Esky Honeybee FP - Replacement of the main motor.

With the new tailmotor installed, the honeybee FP was perfectly controlable again. The only thing now was that it flew only for about 3 minutes with a fully charged 7.4V Lipo.

The mainmotor had lost power too from all those flying hours. So I've replaced the main motor too. This is an easy job done within 5 minutes. I took off the heat sink and cut the strip that held all the wires a bit together.

I first unscrewed the main motor. It is held in place by two screws at the bottom. By rotating the main gear the second screw becomes visible through one of the holes at the surface of the main gear.

The wires of the main motor are attached to the "4 in 1" receiver. You can easily plug them out.

The new main motor. It comes with two new screws.

The new motor screwed on and wires plugged in. Old screws next to the skids.

The bottom looked like this. Time to make a test hover. The helicopter made a strange noise and had almost no lifting power.

After a close examination I found out that the teeth of the motor made poor contact with the gear. I loosened the screws a little and pushed the motor more towards the gear. Very tight this time.

This also resulted in a strange noise while rotating and the heli had also almost no lifting power.

The third time the grip was not too tight nor too loose. The middle way. (sounds like Buddha ;-)

This time it worked perfectly and I had an outside flight of 8+ minutes.

Flies like new !

Esky Honeybee FP - replacement of the tail motor

I love this helicopter because you can fly it, crash it and repair it relatively easy and fly it again. After some time, approx. 10 hours they say, the tail motor loses its power.

Then there's not enough power for the torque. The helicopter loses its yaw to one direction. Its nose and tail then turn only one direction and that makes the heli uncontrolable.

First I had to desolder the two wires.

That's easy.

I removed the screws that keep the motor in place.

The new tail motor. Screws inclusive.

I mounted the new tail motor and soldered the wires on. I connected the wires the same way as they cam off. BUT... the tailrotor spinned the wrong way.

Therefore I reversed the rudder on the transmitter.

A brief indoor check. Hey, my honeybee is back ! ! !

E-Sky Honeybee FP - upgrades & modifications

I've repaired my honeybee FP

It's got a different look. I took the whole machine apart, bit by bit and rebuilt it.
It has a new, red canopy.

The tail fin has moved forward so it doesn't block any air from the tailrotor.

New skids (Extreme-Parts). They can take bad landings better than the stock skids.

The flybar paddles are centered.

A heat-sink installed on the tailmotor. In order to replace the tail boom I had to solder the wires on the tailmotor.

A heat-sink on the main motor.

To mount the battery I use now two rubber bands.

The battery mounted. Right under the 4 in 1.

With the red canopy on.

An orange antenna pipe.

Checking the helicopter indoor. The honeybee flies just FINE ! ! !

My heli's stay on the ground.

The Honeybee against the blue sky.

The Dauphin indoor flight.

Both helicopters need repairs at the moment. I need 2 new motors for the Dauphin but they are hard to get. Out of stock.

The Honeybee FP needs a new flybar and a new tail boom. Flybars are also out of stock and I've used up the bars of the training gear.

E-Sky Honeybee FP - Flybar repairs.

I had some practice flying the Honeybee FP so I removed the training gear set with the 4 ping-pong balls. That soon resulted in a crash and a broken flybar.


I have no spare flybar but I thought I could use a stick from the training gear set.

I had to find out how to remove the broken flybar first. It's tightened with two screws pointing down.

I cut the stick from the training gear set to the correct length and assembled the flybar with the paddles

The flybar was centered and no adjustements had to be made. The Honeybee is good to fly again. ! (Hopefully)

That flies ok... till I made a piloting mistake.. and down the yellow Honeybee went.

That looks not too bad. Putting the battery back in its place.

The main blades go back in their place. Checking everything for a last time and then then...

Airborne again ! ! !

I've crashed many times already but I consider crashing part of the learning curve.

Flying the E-sky Honeybee FP is a lot more difficult than flying a coaxial helicopter but I'm starting to get the hang of it.

Flying this helicopter is a certain feeling that you have to become used to. It's like learning to ride a bicycle. Once you get it, you cannot unlearn it. It takes practice to improve.

(pictures my bro and me)

The E-Sky Honeybee FP. (Fixed Pitch)

A package came in. Yeah my new helicopter has arrived.

Let's see what's in this box. Some spare parts and a training set.

Nice picture on the box. Would the content of the box be as good ?

Flying manual + Simulator software + List of all parts used in the Honeybee FP.

That looks great !!!

It came with a lipo battery. I ordered an other type of battery at the same time but I can't charge that one. I've got no charger. It also came without an adapter for the lipo charger. I had one for the E-Sky Dauphin.

Posing while it's still undamaged ;-))

With the training set installed. Ready for its maiden flight.

That didn't end up well !